Established 1893 | BS 460:2002 Certified | UK & International Supply | Expert Technical Support | 0333 987 4452
Call for Price
H25 – Socket and spigot large box cast iron guttering.
This large box cast iron rainwater system is suitable for larger
buildings and industrial and railway heritage projects, and is available in
the following sizes:
100 x 100mm
125 x 100mm
150 x 175mm
150 x 100mm
The TFH25 is a large sand cast box gutter in socket and spigot form — a right-angled, square-sectioned profile that provides maximum drainage capacity in a compact, architecturally unobtrusive form. Box gutters are typically specified where the design or condition of the parapet, valley, or eaves detail requires a concealed or near-flush gutter rather than an exposed decorative profile.
Available in four sizes: 100×100mm, 125×100mm, 150×100mm, and 150×175mm. The socket and spigot joint provides a clean, secure connection between sections. Suited to large Victorian and Edwardian buildings, civic architecture, churches, and industrial heritage projects where a high-capacity concealed gutter system is required.
Sand cast iron, manufactured to BS 460:2002. Supplied in grey primer or black painted finish. Lead times are typically 8–10 weeks. Contact Tuscan Foundry Products to discuss sizing, fittings, and project requirements.
Suitable for: Parapet and valley gutter applications, large civic buildings, churches, industrial heritage. Call for price: 0333 987 4452.
Casting of iron is an imperfect processs. It is possible with some cast iron radiators that you will get minor imperfections in the surface finish. When radiators are painted this will reduce and over the years every additional coat of paint applied will provide a smoother more equal finish.
Our cast iron hopper heads are available in a standard primed and black-painted finish, ready for on-site topcoats. Heritage colour finishes and factory-applied linseed oil paint are available on request. Linseed oil paint is a vapour-permeable, period-appropriate finish particularly well suited to listed buildings and conservation area properties.
Prices are shown on the product page. For project quantities, multiple pattern orders, or a formal quotation, call 0333 987 4452 or use the contact form.
The H542A measures 240mm wide x 240mm deep x 290mm high, making it well suited to a compact square profile suited to smaller Georgian and Victorian properties, extensions and outbuildings.
Our brackets are more commonly used on cast iron rainwater systems. Unlike plastic, cast iron is heavy and the weight keeps the gutter in position. As such our brackets do not normally have retaining clips which could lead to plastic or lightweight gutters blowing out of the bracket. The profile of your gutter should match that of our bracket but without the weight to keep it in place you may well encounter problems in bad weather.
Yes. A polished brass finish is historically appropriate for period buildings and is generally acceptable to conservation officers for listed building projects. If you are unsure about the specification requirements for your project, we are happy to advise — call 0333 987 4452.
Polished chrome has a bright mirror finish, while satin chrome has a brushed, low-sheen appearance. Both are available in the telescopic hand winder range. The finish choice typically depends on the ironmongery specification for the project.
Our cast iron airbricks are available in three standard sizes: 225mm × 75mm (single course), 225mm × 150mm (double course), and 225mm × 225mm (square format). These correspond to the standard airbrick positions used in Victorian and Edwardian brickwork. Each size is available across the School Board, Louvre, and Ornamental pattern ranges.
The H532 measures 560mm wide x 290mm deep x 305mm high, making it well suited to a broad, low-profile design suited to substantial roofs and box gutters on period commercial and civic buildings.
Yes. All our mild steel brackets are supplied in either silver or black zinc plate. This coating protects the metal however, both will need painting prior to installation.
We have chosen to use zinc plating for two reasons; firstly that it is a more environmentally friendly than galvanising and secondly that it does not block up the threaded part of the rise and fall cups in the way that galvanising does.
