Established 1893 | BS 460:2002 Certified | UK & International Supply | Expert Technical Support | 0333 987 4452
Call for Price
Cast iron rainwater Head H532. Created using bespoke cast iron hopper pattern H532.
Cast iron leader heads for period, listed and traditional buildings.
(Bespoke cast iron rainwater heads and ornamental hoppers manufactured to order)
The Ashwell No.532 is a wide, low head with canted ends and very little ornament — the quiet member of the group, and the one that solves awkward geometry.
The body is a broad, shallow box with the ends cut back on the splay. Simple raised mouldings run along the top and bottom edges, framing an otherwise plain face. The outlet drops from the underside. That is the whole design, and its usefulness lies in the proportions rather than the detail.
Width without height is what the pattern offers. Where a string course, a band course, a shallow eaves overhang or a low parapet leaves only a limited vertical zone for the hopper, a tall head simply will not fit without cutting across a moulding. The Ashwell spreads the same collecting area sideways and stays within the available band. The canted ends soften what would otherwise be a hard rectangular block against the wall, and reduce the visual weight at the point where the casting meets the elevation.
It suits later Georgian and early Victorian elevations, terraces with strong horizontal banding, estate and agricultural buildings, and any scheme where the rainwater goods should be competent and unobtrusive rather than decorative.
Cast in solid iron to BS 460:2002 and supplied in primer or black as standard, with heritage colours and traditional linseed oil finishes available on request.
Pipe connections: 65mm, 75mm and 100mm round; 75×75mm, 100×100mm and 125×125mm square; 100×75mm, 125×100mm and 150×125mm rectangular.
Suitable for listed buildings and conservation areas. If the available height is tight, send us a section or a photograph and we will confirm the fit — call 0333 987 4452.
| Finish | Primer, Black |
|---|---|
| Connection | 65mm Round, 75mm Round, 100mm Round, 75mm x 75mm Square, 100mm x 100mm Square, 125mm x 125mm Square, 100mm x 75mm Rectangular, 125mm x 100mm Rectangular, 150mm x 125mm Rectangular |
The satin chrome telescopic rooflight hand winder opener is available in multiple sizes. The telescopic mechanism adjusts to accommodate varying rooflight positions and throw requirements. For a full list of available sizes, visit tuscanfoundry.com or call 0333 987 4452.
The right size depends on the width of your gutter run and the volume of water you need to collect. The Strayton H42A is available in four widths: 305mm (12"), 355mm (14"), 457mm (18"), and 610mm (24"). As a general guide, wider hoppers suit larger roof areas and heavier rainfall zones. If you are unsure, our team can advise based on your gutter profile and catchment area — call 0333 987 4452.
For rooflights directly above a worktop or sink, a telescopic screw-jack hand winder is the most practical choice. Available in polished brass, satin chrome, and polished chrome, these openers allow controlled ventilation from a fixed handle position without requiring a pole. The 150mm or 250mm size is typically appropriate for standard-height kitchen rooflights.
The Antique Black finish is cast iron with a blackened surface — the most historically accurate finish for cast iron ironwork and the most appropriate for the majority of heritage applications. Polished Lacquered is cast iron with a bright polished surface sealed with clear lacquer, suited to interiors and sheltered locations where polished ironwork is the specification. Polished Brass is solid polished brass throughout — the correct choice where existing building fittings are in brass or where a warm metal tone is required.
Yes. Cast iron hopper heads are the historically appropriate choice for listed buildings, and are generally preferred by conservation officers and local planning authorities over modern plastic alternatives. Tuscan Foundry cast iron hopper heads are manufactured in solid grey iron and are suitable for use on listed buildings and within conservation areas. A linseed oil finish is also available, which is particularly appropriate for sensitive heritage projects.
Our bespoke rise and fall gutter brackets — including fascia, side rafter, and top rafter variants for Osma Roofline and Osma SuperLine systems — are manufactured to order. The standard lead time is 10–14 working days from receipt of a confirmed order. If you have a programme deadline, please call us on 0333 987 4452 and we will advise on current availability.
The H1A is available with round pipe connections in 65mm, 75mm, 100mm, and 150mm diameters. Please specify your required connection size when ordering, as this determines the SKU. If you are unsure of the correct pipe size for your project, our team can advise — call 0333 987 4452.
Our cast iron hopper heads are available in a choice of finishes including primer, painted, and specialist heritage finishes. Please call us on 0333 987 4452 or submit an enquiry to discuss the right finish for your project.
In most cases, replacing like-for-like cast iron guttering on a listed building does not require Listed Building Consent (LBC), provided the replacement matches the existing profile, material, and finish exactly. However, any change of material away from cast iron will almost always require consent. We recommend consulting your local conservation officer before proceeding, and we can provide specification documentation to support your application if required.
Please call 0333 987 4452 or use the contact form with the size, quantity and connection details, and we'll provide a quotation.
