Established 1893 | BS 460:2002 Certified | UK & International Supply | Expert Technical Support | 0333 987 4452
Call for Price
H14Si – Large moulded cast iron guttering.
This large moulded cast iron rainwater system is suitable for larger
buildings and industrial and railway heritage projects, and is available in
the following sizes:
150 x 150mm
The TFH14Si is a large sand cast moulded cast iron gutter in the 150×150mm size — a deeper, more square-sectioned profile in the TFH14 moulded family. The increased depth relative to face width gives the TFH14Si significant drainage capacity, making it appropriate for buildings with steep roof pitches, large catchment areas, or where a particularly deep gutter section was original to the building.
The 150×150mm size places the TFH14Si in the very large end of the sand cast range — a profile typically encountered on substantial civic buildings, large Victorian institutional architecture, country houses and estate buildings, and industrial heritage projects where standard profiles are simply too small.
Sand cast iron, manufactured to BS 460:2002. Supplied in grey primer or black painted finish. Lead times are typically 8–10 weeks. Contact Tuscan Foundry Products to discuss your project requirements in detail before ordering.
Suitable for: Large civic buildings, country houses, estate architecture, Victorian institutional buildings, industrial conservation. Call for price: 0333 987 4452.
Yes. Cast iron hopper heads are the historically correct choice for listed and period buildings, and a like-for-like cast iron replacement is generally accepted without objection by conservation officers. We manufacture to BS 460 for genuine heritage character and durability.
Prices for standard cast iron hopper heads are shown on the product page. For larger quantities, bespoke sizing, heritage colour finishes, or full rainwater system specifications, please call 0333 987 4452 or use the contact form.
The in-house Premier Extra coating is formulated for a life expectancy of around 10 years under normal weather conditions, provided any impact damage or surface scuffing is made good promptly. Coastal locations or higher pollution levels can shorten this, so it's worth asking your local stockist or paint manufacturer for site-specific advice.
The right size depends on the width of your gutter run and the volume of water you need to collect. The Strayton H42A is available in four widths: 305mm (12"), 355mm (14"), 457mm (18"), and 610mm (24"). As a general guide, wider hoppers suit larger roof areas and heavier rainfall zones. If you are unsure, our team can advise based on your gutter profile and catchment area — call 0333 987 4452.
Prices are shown on each product page. For project quantities, bespoke specifications, or conservation-related queries, please call us on 0333 987 4452 or use the contact form on our website.
Yes. A polished brass finish is historically appropriate for period buildings and is generally acceptable to conservation officers for listed building projects. If you are unsure about the specification requirements for your project, we are happy to advise — call 0333 987 4452.
The Cast Iron Louvre Airbrick suits Victorian and Edwardian terraced housing, semi-detached properties, public houses, agricultural buildings, and workshop structures where the original airbrick was a louvre-face grille. The horizontal fin profile is widely found in British domestic and light industrial construction from the 1870s through to the 1950s.
Hopper heads are supplied in red oxide primer ready for on-site painting, or pre-finished in black. A full range of Heritage Colours in traditional linseed oil paint is also available on request — please contact us for the swatch chart.
The opener is designed for use with Lumen Rooflights and compatible timber-framed skylights. The telescopic shaft and adjustable mounting bracket allow it to be fitted to a range of rooflight frames. If you have a specific rooflight model, call us on 0333 987 4452 to confirm compatibility.
All of our cast iron radiators are availbale as standard with a 1/2″ BSP (15mm) connection. We are though also able to supply many of our radiators and valves with 3/4″ BSP connections. Due to the size proportions of some radiators and valves 3/4″ connections may be more suitable.
