Established 1893 | BS 460:2002 Certified | UK & International Supply | Expert Technical Support | 0333 987 4452
Price range: £40.30 through £42.82 ex VAT (£48.36 – £51.38 inc VAT)
Rise and Fall bracket for the H16 Moulded Gutter
UK delivery from £30. Fittings are despatched boxed. See delivery rates.
The H16 rise and fall bracket provides adjustable support for the Regent No.16 moulded ogee gutter, allowing precise fall setting at each bracket position independently of the fascia or rafter angle. On the large Victorian and Edwardian properties, country houses, civic buildings, and institutional buildings where the H16 No.16 is typically found, long gutter runs and complex roof lines make adjustable fall control particularly valuable.
The threaded rise and fall cup allows the gutter height to be set accurately at each bracket position, eliminating the need for shimming or packing and ensuring correct drainage gradient across the full run. The bracket cup is shaped for the H16 moulded cross-section. Available in both H16 sizes: 125×100mm (5″×4″) and 150×100mm (6″×4″).
Supplied in primed or factory black finish. For listed buildings and heritage projects where the H16 No.16 moulded pattern is the original profile. For specification support, call 0333 987 4452.
| Size/Finish | Primer 125mm x 100mm, Primer 150mm x 100mm |
|---|
Our cast iron hopper heads are available with 65mm, 75mm and 100mm round outlets, 75mm, 100mm and 125mm square outlets, and 100x75mm, 125x100mm and 150x125mm rectangular outlets, to match the downpipe already on site or specified for the project.
The satin chrome telescopic rooflight hand winder is well suited to contemporary and transitional interiors where a brushed chrome finish complements modern or minimal ironmongery. It is compatible with Lumen Rooflights and timber-framed skylights.
Hopper heads are supplied in red oxide primer ready for on-site painting, or pre-finished in black. A full range of Heritage Colours in traditional linseed oil paint is also available on request — please contact us for the swatch chart.
The Gothic foliate tracery design of the Ornamental Airbrick provides a good free-flow ventilation area relative to its face size. The open area is comparable to other standard cast iron airbrick patterns. The visual density of the pattern at a distance reads as solid ironwork, which suits formal and decorative elevations without compromising subfloor ventilation effectiveness.
The satin chrome telescopic rooflight hand winder opener is available to order at tuscanfoundry.com. For project or volume enquiries, call 0333 987 4452 or use the contact form on our website.
The Brass Rooflight Hand Winder Opener – Telescopic is available in 150mm, 250mm, and 300mm sizes. The telescopic mechanism provides flexibility to accommodate varying rooflight positions and throw requirements. Throw: 165mm.
The Cast Iron Louvre Airbrick (F020802AFC) is available in 225mm × 75mm, 225mm × 150mm, and 225mm × 225mm — standard brick course heights. All sizes share a consistent depth for straightforward like-for-like replacement of original cast iron louvre airbricks.
It is possible for us to supply towel warmers with an electric heating element in them. The Electrad system is a unique system available to us, that enables independent heating of towel rails and radiators via the properties electrical system.
Our cast iron airbricks are available in three standard sizes: 225mm × 75mm (single course), 225mm × 150mm (double course), and 225mm × 225mm (square format). These correspond to the standard airbrick positions used in Victorian and Edwardian brickwork. Each size is available across the School Board, Louvre, and Ornamental pattern ranges.
The polished chrome telescopic rooflight hand winder is suited to contemporary, Georgian-revival, and high-specification interiors where a bright chrome finish is required to complement existing ironmongery. It is compatible with Lumen Rooflights and timber-framed skylights.
