Established 1893 | BS 460:2002 Certified | UK & International Supply | Expert Technical Support | 0333 987 4452
£31.25 ex VAT (£37.50 inc VAT)
Contains jointing strip, bolts, washers and nuts to complete 10 joints on Half Round, Beaded Half Round and Deep Half Round Gutters. For Ogee and No.46 Moulded profiles the jointing strip is replaced with U9 silicone.
UK delivery from £30. Fittings are despatched boxed. See delivery rates.
The gutter jointing kit contains all the components needed to complete 10 joints on a cast iron gutter run: jointing strip, bolts, washers, and nuts. The jointing strip seals the socket-and-spigot joint between gutter sections, providing a flexible and waterproof seal that accommodates the thermal movement of cast iron guttering. The bolts, washers, and nuts secure the union clips that mechanically connect each joint.
Compatible with standard half round, beaded half round, deep half round, moulded ogee, G46, and Notts OG profiles. For ogee and No.46 moulded gutter, only the bolts are used — the jointing strip is not applicable to these profiles. The kit format ensures all components are available together, avoiding the delays and additional cost of ordering jointing materials and fixings separately. For specification support, call 0333 987 4452.
The Brass Rooflight Pole Winder Opener 300mm is a screw-jack operated rooflight opener designed for manual control of timber-framed skylights and Lumen Rooflights. The 300mm fixed arm is suited to standard rooflight positions and is finished in polished brass.
Our cast iron hopper heads are available with 65mm, 75mm and 100mm round outlets, 75mm, 100mm and 125mm square outlets, and 100x75mm, 125x100mm and 150x125mm rectangular outlets, to match the downpipe already on site or specified for the project.
Yes. Cast iron hopper heads are the historically correct choice for listed and period buildings, and a like-for-like cast iron replacement is generally accepted without objection by conservation officers. We manufacture to BS 460 for genuine heritage character and durability.
Our cast iron hopper heads are available with 65mm, 75mm and 100mm round outlets, 75mm, 100mm and 125mm square outlets, and 100x75mm, 125x100mm and 150x125mm rectangular outlets, to match the downpipe already on site or specified for the project.
Prices are shown on the product page. For project quantities, specification support, or a formal quotation, call 0333 987 4452 or use the contact form.
BTU stand’s for British Thermal Units. This was the old (Imperial) measurement for heat in connection with plumbing. Although BTU’s is a term still commonly used within the heating and plumbing, the industry is now going over to KW’s Kilowatts.
Yes. Cast iron airbricks are the appropriate material for listed buildings and conservation area properties where the original ventilation grilles were cast iron. They maintain the character and material authenticity required by most conservation officers and listed building consent conditions. We recommend confirming the specific pattern with your conservation officer before ordering.
Traditional Express (TX) is a cast iron push-fit soil system. Socketless pipes are joined with push-fit sockets and couplings using rubber seals, so there is no caulking on site. LCC uses caulked socket-and-spigot joints and a bitumen coating. TX is quicker to install and can be painted; LCC is the closer match to an original Victorian stack. Our Traditional Express vs LCC guide compares the two in detail.
Traditional Express can be painted, including in our linseed oil finish. LCC is supplied with a black bitumen coating, which cannot be reliably overpainted with conventional paints; maintain it with a compatible bituminous paint. Where a painted soil stack is required, specify Traditional Express.
Victorian properties most commonly used Ogee (OG) gutter profiles, including the standard Cast Iron Ogee and the G46 Moulded Ogee. Half Round guttering was also widely used, particularly in the later Victorian period. The correct profile depends on what is already present on the building — we recommend inspecting any surviving sections and matching the profile, size, and socket direction exactly. We supply 19 standard gutter profiles and can copy-cast any non-standard profile from a drawing, photograph, or physical sample.
